Home | New Products (page 3)

New Products

FAST® Precision-Flow™ 242 lbs/hr High-Impedance Fuel Injectors

32107-8

New FAST® Precision-Flow™ 242 lbs/hr High-Impedance Fuel Injectors deliver improved idle quality, throttle response and flow consistency in any EFI engine. The injectors are some of the highest flowing available (rated at 58 psi) and designed for drop-in installation in many EFI manifolds, including GM Gen III and IV LS manifolds when using the included special sized O-ring. Methanol and ... Read More »

FAST® FireWire Cut-To-Fit Spark Plug Wire Sets for GM LS Coils

LS Wires-45

The latest FAST® FireWire® Cut-to-Fit Wire Set provides high performance with a customizable length for LS coils in stock or non-stock locations. At 9mm in diameter and with 15 ohms per foot resistance, the wires are ideal for boosted applications and high-compression engines. A reactive core design reduces electro-magnetic (EMI) interference, while a silicone-on-silicone sleeve offers abrasion and heat resistance. ... Read More »

COMP Cams® Hustler™ Lifters for GM 604 Crate Engines

ST123-1

Memphis, TN – COMP Cams® Hustler™ Lifters for GM 603 & 604 Crate Engines look stock but offer superior performance in race applications with tight rules packages. The new lifters feature reduced internal piston travel for increased stiffness and greater valve lift when compared to stock lifters in sealed GM 603 and 604 crate and 1987-1998 GM small block engines. ... Read More »

COMP Cams® Hustler™ Camshafts for GM 604 Crate Engines

08-694-3-b

Memphis, TN – COMP Cams® has created a Hustler™ camshaft series featuring two new billet camshafts, as well as two regrind options, for GM 603 and 604 Crate Engines owners wanting to press the rules a bit. The Stage 1 billet cam is ground to the same factory lobe lift, but with three degrees more duration and a lobe that ... Read More »

COMP Cams® Cam Phaser Lockout Kit for GM L92, L94, L9H & Gen V LT Engines

5465

Memphis, TN –New COMP Cams® Cam Phaser Lockout Kits for GM L92 & Gen V LT engines allow engine builders and enthusiasts to eliminate variable valve timing (VVT) in specific GM applications, making the installation of larger camshafts possible for big power gains. This phaser lockout kit includes a plug that prevents the VVT phaser from moving the camshaft. The ... Read More »

COMP Cams® Cam Install Kits for GM LS Applications

5622

Memphis, TN – COMP Cams® Cam Install Kits offer an all-in-one gasket and hardware solution for enthusiasts wanting to swap their GM LS camshafts. These simple kits feature essential water pump and front cover gaskets, as well as needed cam and crank bolts.  Additionally, the crankshaft seal and other commonly overlooked gaskets are included. Unlike other kits on the market, ... Read More »

COMP Cams® Beehive™ LS6+ Valve Springs for GM LS Applications

OLYMPUS DIGITAL CAMERA

Memphis, TN –COMP Cams® introduces Beehive™ LS6+ Valve Springs for GM LS Applications, an improved option over popular GM LS6 valve springs. Improving upon the “blue” GM LS6 factory valve spring, COMP Cams® LS6+ valve springs allow for 4% higher seat and open loads for better dynamic control, as well as an extra .030” of lift capability. These springs are ... Read More »

COMP Cams® 1.550 High-Lift Dual Valve Springs for Racing Applications

26547-16

Memphis, TN – COMP Cams® has again raised the bar with the release of their new 1.550″ High Lift Dual Valve Springs for racing applications. COMP Cams® 1.550″ High Lift Dual Valve Springs are made specifically for high endurance roller camshaft applications with up to .900” valve lift that operate under extreme, high-RPM conditions such as circle track, drag, marine ... Read More »

COMP Cams® .700 Max Lift Dual Valve Springs for GM LS7, LT1 & LT4 Engines

26527

Memphis, TN – COMP Cams® introduces a new .700″ Max Lift Dual Valve Spring that uses the additional installed height available in newer stock GM LS7, LT1 and LT4 engines to increase valve lift capacity and improve valve control. These new valve springs are optimized to improve performance in engines with taller installed heights. Capable of sustaining up to .700” ... Read More »

COMP Cams® Thumpr™ Camshaft Packages for GM LS Applications

Screen Shot 2018-11-01 at 5.05.17 PM

Memphis, TN – COMP Cams® Thumpr™ Camshaft Packages for GM LS Applications combine the outstanding sound of COMP Cams® Thumpr™ Cams with the ease of getting a complete valve train parts package matched to your specific GM LS application and desired performance level. COMP Cams® engineers have spent countless hours testing and creating valve train component combinations that are perfectly ... Read More »