Welcome to CPGNation.com! Log in or Sign up to interact with the CPGNation community.
maxwell
Last Activity:
May 14, 2018
Joined:
Jul 5, 2012
Messages:
2,056
Likes Received:
29
Trophy Points:
48

Following 1

Followers 2

Share This Page

maxwell

Moderator

Staff Member
maxwell was last seen:
May 14, 2018
    1. lr057
      lr057
      Hi i have a rebuilt mk4 454 short block with flat top pistons and wanting to put a retro fit roller cam in it .The heads are gm 781 with large valves installed and some pocket work done as well with 115 cc chambers. The compression is 8:5:1 what retro fit roller cam should i install. 67 camaro with 4speed muncie and 3.08 diff gears , 245/45/18 rear tyres. Can i run a marine cam with low duration and 112 lobe
    2. upper_decker
      upper_decker
      I have a 08-501-8 cam, and I am wondering what kind of distributor gears I can run on it. I purchased the 12200 gear, but my distributor has a .427" shaft. I am thinking about buying the msd 5592 distributor, but that has a melonized gear. I definately DON'T want to tear this build up over such a small and inexpensive part like a distributor gear.
    3. Fred Richards
      Fred Richards
      I'm running a 12-236-3 cam from you. It's on a fresh sbc bored .030 with Vortec heads that just have springs redone. Performer intake that is bored. 18 lb spring with 350 injectors. The question is, what kind of manifold vacuum should I expect. I'm at 15 at idle. Chasing a problem of being too rich. Thought maybe vacuum to low.
    4. shelbydogg
      shelbydogg
    5. JMAN21
      JMAN21
      I spoked in the FAST forum on Monday. It says 'waiting for moderator approval before public'....any chance we can get this approved? I need this post up so I can get some help... Thx
    6. rtk
      rtk
      My posts are not being allowed and are held in the moderating approval and when I try to edit the post I get an error and a comment about a spam like post can you explain it for me please
    7. MN80Vette
      MN80Vette
      I am new to CPG Nation/FAST Support group. I posted first question yesterday titled, "FAST EZ EFI 1.0 won't idle after driving". The status says, "Awaiting moderation before being displayed publicly." I don't know what that means and it's not mentioned in Help. I noticed you are a Moderator, so I thought I should ask, is there something I need to do to have it "moderated"? Thanks.
    8. Dart67
      Dart67
      Is there a problem with the forum ?

      I can see the topics but am unable to load and read them.

      Thanks,

      Herb
    9. ArniFPR
      ArniFPR
      Thanks for the info but i was wondering if the exhaust cam is also from comp
      here are the photos
      http://honda-tech.com/showpost.php?p=49234727&postcount=15

      it has A25 stamped to the end and there are something etched on to them but i'm not sure what it say's but i think it is 57103


      with best regards
      Arni
    10. ArniFPR
      ArniFPR
      Thanks for the info but i was wondering if the exhaust cam is also from comp
      here are the photos
      http://honda-tech.com/showpost.php?p=49234727&postcount=15

      it has A25 stamped to the end and there are something etched on to them but i'm not sure what it say's but i think it is 57103


      with best regards
      Arni
    11. orbot
      orbot
      I sent an email, im the guy asking for a small base circle cam (XE262H) for a 350 small block chevy, thanks.
    12. orbot
      orbot
      I sent an email, im the guy asking for a small base circle cam (XE262H) for a 350 small block chevy, thanks.
    13. maxwell
      maxwell
      No problem at all, Rick. I was actually about to reply to your post. I was out on Friday and that has put me behind a bit. I will put the specs on the forum. PM me your email address and I will be able to give you an actual spec card.

      Thanks,
      Matt
    14. maxwell
      maxwell
      No problem at all, Rick. I was actually about to reply to your post. I was out on Friday and that has put me behind a bit. I will put the specs on the forum. PM me your email address and I will be able to give you an actual spec card.

      Thanks,
      Matt
    15. quicktime
      quicktime
      hi there, i noticed you are one of the senior techs on here,and that you have quite the knowledge on specs,parts numbers,etc with everything related to comp cams..i had posted a thread asking around for some cam specs on two smallblock ford hydraulic roller cams that i have..was wondering if maybe you can help me out? not trying to be a bother,and if you don't have the time,too busy,etc i'll understand totally..Rick
    16. quicktime
      quicktime
      hi there, i noticed you are one of the senior techs on here,and that you have quite the knowledge on specs,parts numbers,etc with everything related to comp cams..i had posted a thread asking around for some cam specs on two smallblock ford hydraulic roller cams that i have..was wondering if maybe you can help me out? not trying to be a bother,and if you don't have the time,too busy,etc i'll understand totally..Rick
  • Loading...
  • Loading...
  • Signature

    Matt Maxwell
    Technical Consultant
    Product Specialist
    COMP Performance Group